Céghírek

Butt Welding Machine Do The Inspection Work Regularly

2018-11-15

Butt Welding Machine The equipment needed for welding process----welding equipment, including welding machine, welding process equipment and welding aids.

Minden hegesztési munkával foglalkozó vállalkozás vagy egyén teljes körűen kívánja teljesíteni a berendezés teljesítményét és meghosszabbítani a gép élettartamát. E cél elérése érdekében a hegesztőberendezések helyes használata a működési eljárásoknak megfelelően, valamint a rendszeres karbantartási és karbantartási munkák mellett. A fáklya, a huzaladagoló és a hegesztőgép karbantartási pontjain az alábbiak ismertethetők.

I. Karbantartás Butt hegesztőgép

1. Rendszeresen ellenőrizze és cserélje ki a vezetőképes fúvókát.

Mivel a kopott vezetőképességű fúvóka átmérője nagyobb lesz, az ív instabil, a hegesztési megjelenés romlik, vagy a ragadós huzal (visszaégésre), a vezetőképes fúvóka vége ragasztásra kerül a fröccsenéshez, a huzalelőanyag nem lesz sima, a vezetőképes a fúvókát szorosan csavarják, a menetes csatlakozás felmelegszik és meghal.

2. A rugótömlő rendszeresen tisztítható és cserélhető.

Spring Hose long time after use, will accumulate a large number of iron powder, dust, wire, such as the plating, so that the wire feeding instability. So it's important to clean up regularly, curl it and tap it, shake it off, and blow it off with compressed air. The grease on the hose should be washed in the oil with a brush and then blown with compressed air. Spring hose If the wrong wire or serious deformation bending, it is necessary to replace the new hose. The tube should be confirmed to be suitable for the diameter and length of the wire used, and do not appear burr in the cut-off surface.

3. Ellenőrizze a szigetelőgyűrűt.

If the insulation ring is removed, the splash will be glued to the nozzle to guide the nozzle with the electrically charged part. The torch may be burnt by short circuit. At the same time, in order to protect the gas flow evenly, must be fitted with insulation rings.

II. Maintenance of wire feeding equipment

1. Add nyomásszabályozás

The wire feeding roller pressure should be adjusted according to the diameter of the wire. If the pressure is not enough, the wire will slip, the pressure is too large, welding wire will be carved, deformed. If the use of cored wire, wire feeding wheel to add pressure than the solid wire smaller.

2. A huzalkiegyenlítő eszköz beállítása

The adjustment method of the welding wire straightening device varies according to the type of machine, and should be adjusted to the suitable position of the welding wire diameter According to the manufacturer's mark.

3. Welding Wire Plate Installation

Ha a telepítés nem a helyén van, a huzallemez a leesés kockázatának elfordulásakor súlyos következményekkel jár. Ellenőrizze, hogy a féktárcsa vagy a retesz megbízhatóan van-e felszerelve.

4. A vezetékek adagoló kerekei és az alkalmazott vezetékek átmérője

It must be fitted with a wire feed wheel suitable for the diameter of the wire, and check whether the number engraved on the roller is consistent with the diameter of the wire.

5. The abrasion and fouling of the wire feeding roller groove

Check the wire roller groove whether wear, groove surface is carved, whether the groove adhesion dust, iron powder, wire plating, etc. Wipe with cotton cloth and so on when cleaning.

6. Guide Silk Mouth Inspection

Installed in the wire feed wheel before and after the guide silk mouth wear or with the wire feed wheel is not horizontal, it will lead to wire bending, wire feed instability, therefore, must be regularly inspected and repaired.

Third, the maintenance of welding machine

First of all, it is necessary to note that in the implementation of welding machine internal or external connectors Terminal inspection, the power supply switch must be closed before it can be implemented.

1. Do the inspection work regularly. For example, check the welding machine power, the cooling fan rotation is smooth, whether there is abnormal vibration, sound and odor occurs, gas leakage, welded wire joints and insulation of the bandage is lax or peeling off, welding cable and the wiring parts are abnormal heating phenomenon.

2. Mivel a hegesztő a levegőhűtéshez kényszerül, könnyen belélegezhető a környező területről származó por, és felhalmozódik a gépben. Így rendszeresen használhatunk tiszta és száraz sűrített levegőt a por eltávolítására a hegesztő belsejéből. Különösen a transzformátorok, a reaktív tekercsek és a tekercstekercsek a rés és a teljesítmény félvezető részek között, amelyeket speciálisan meg kell tisztítani.

3. Check the wiring parts of power wiring regularly. The force side, the output side of the terminal, as well as the wiring of the external wiring parts, wiring parts of the line and other locations of the wiring screws are loose, rust to remove the rust to make contact with good conductivity.

4. Long-term use of welding machine will inevitably make the shell due to touch and deformation, rust and damage, internal parts will also be killed, so in the annual maintenance and inspection to carry out the replacement of defective parts and shell repair and insulation deterioration parts of the reinforcement and other comprehensive repair work. The replacement of defective parts in the maintenance of the best can be all a times the replacement of new products to ensure the performance of the welder.

The above-mentioned regular maintenance and inspection can reduce the occurrence of welding failure, although it takes some time and energy, but can prolong the life of welder, and can improve the efficiency of operation, ensure the performance of welder and improve safety. is the welding work must not neglect an important content.

IV. Three important points for automatic welding equipment

1, flexible and diverse solder way, at the same time to support spot welding and drag welding (pull welding), automatic solder equipment All the parameters can be set by customers themselves to adapt to a variety of difficult solder operation and micro-solder process, all the solder parameters can be accompanied by the welding point coordinate program read and save, to achieve the flexibility of the solder operation.

2, soldering iron components can be arbitrary angle, arbitrary azimuth adjustment, control of the Iron group of the R-axis, can be 360 degrees of free rotation, according to different pads and components arbitrarily set the number of tin, preheating time and solder time, to achieve a variety of solder joints of the complex welding process, to achieve a variety of solder operations.